How to Make Coasters from Ceramic Tiles
Mar 14, · Instructions: Gather your supplies. Make sure your tile is free of dust and dirt. (I gave mine a quick wipe-down with rubbing alcohol. The alcohol dries Cut scrapbook paper (book pages, wrapping paper – whatever you’re using to decorate your tile coasters) into 4? x 4? Cut felt into 4?x4?. Dec 12, · I sprayed the back of the stencil with spray adhesive and lined it up on my tile. Using a stenciling brush, I painted over the stencil. I highly recommend the stenciling brush it left clean lines versus the foam brush I started with (and is pictured above). Peel the stencil off right away.
Hand-painted ceramic tiles add detail and individuality to any decor, but they can be quite what did abraham lincoln state in the emancipation proclamation. Tiles that will be put to practical use, such as trivets, coasters or tabletops should be fired to make their finish durable. Firing is not possible if the tiles are already affixed to the wall or to a tabletop.
The key to painting ceramic tiles that can't be fired is to start with a durable primer that's compatible with both ceramic surfaces and acrylic paints. Wash your tiles with a mild degreasing cleanser such as dishwashing soap to remove any dust or oils. Dry them thoroughly with a shop cloth, or other lint-free cloth. Pour a small dollop of water-based acrylic paint into a small bowl.
Use one bowl for each color if you are using more than one. Don't pour out too much paint because it dries very quickly. Paint the tiles in your preferred design, letting each color dry before adding the next one, unless you are blending them. Place the painted tiled on a baking sheet with a little bit of space between them.
Bake the tiles according to the time recommended on the paint labels. This varies between manufacturers, so read the labels.
Turn the oven off after the specified baking time, but don't remove the baking sheet. Let the tiles come to room temperature in the oven without disturbing them. Clean your tiles thoroughly with a mild degreasing cleanser such as dishwashing liquid. Rinse away all traces of the soap and dry the tiles with a lint-free cloth. Sand the tiles lightly with grit surface.
Toughing up the finish a little bit helps the primer and paint adhere. Apply a thin, even coat of spray-on primer that is formulated specifically to adhere to surfaces such as ceramic tile. Let the primer dry completely according to the directions on the label. Spray or paint on a thin, even coat of oil- or water-based acrylic paint. Let how to paint tiles for coasters first coat dry completely before applying a second coat. Apply any hand-painted designs after the second base coat has dried.
Spray on a thin, even coat of a how to display rss feed on wordpress page sealer such as urethane or acrylic modified epoxy. Make sure that the area you are sealing is well ventilated and wear your goggles and mask. A running enthusiast who regularly participates in San Francisco's Bay to Breakers run, Chandler works as an independent caterer, preparing healthy, nutritious what does msm do for joints for Phoenix area residents.
By Brynne Chandler. Related Articles. Tips Sketch your design or practice stencil designs on paper before painting the actual tile to avoid mistakes. Don't paint wall tiles that will be repeatedly exposed nov 11 1918 what happened water without sealing them or the paint will chip, peel and eventually wash away.
Tiles Make the Best Coasters
Apr 16, · Step 1: Begin by prepping your ceramic coasters by covering the backside with painters tape. This will make sure that as the paint drips off your coaster the bottom stays nice and clean. Step 2: Pour a small amount of the DecoArt Pouring Medium into one of your small paint cups or containers. Step 3. Sometimes I get asked how to make coasters by directly hand-painting on them, so here's how: You can paint on your tiles using special oven-bake ceramic paint like the Pebeo Vitrea paints, bake them (using the instructions that come with the paint), and then coat the tiles with envirotex like I describe on the rest of page. Check out these adorable hand-print tiles made by reader Felicity and . Spray or paint on a thin, even coat of oil- or water-based acrylic paint. Let the first coat dry completely before applying a second coat. Apply any hand-painted designs after the second base coat.
Can you guess what it is? They're not waterproof! Seems silly, right? But it's true. I know, because I tried them. The ceramic tile coasters that I crafted looked great initially, but very quickly got tea and coffee stains on them that wouldn't wipe off. Not being waterproof is a pretty serious problem for a coaster! I tried all sorts of things to make the coasters waterproof.
On my third or fourth attempt I finally figured out how to make coasters that were immune to tea and coffee drips. I'll share the secret with you on this page so you can learn how to make coasters that are beautiful, durable, and fully waterproof. It's actually pretty simple once you know how. I'll show you how to make coasters in batches of four, though obviously you can make as many or few as you like.
I think they make really lovely gifts. I gave this set to my mom for Christmas which I made using some beautiful Japanese paper. And here's a gratuitous photo of my DIY ceramic tile craft coaster with one of my favorite Denby teacups. If you're wondering how to make coasters with photos, you can use the exact same method. Here's one made by reader Shelbie thanks for sending in the pic Shelbie! Here's a beautiful tile by artist Judy Blasdell. She printed her design on a water slide decal and then varnished using the method I'll show you on this page.
Here's an awesome set coasters featuring Star Wars bounty hunters, by Jason from Drexninestudios. The artwork was hand-painted, scanned, given a digital background in post-production, then printed and glued onto the tiles using the method on this page. Sometimes I get asked how to make coasters by directly hand-painting on them, so here's how: You can paint on your tiles using special oven-bake ceramic paint like the Pebeo Vitrea paints , bake them using the instructions that come with the paint , and then coat the tiles with envirotex like I describe on the rest of page.
Check out these adorable hand-print tiles made by reader Felicity and her two-year-old daughter. Thanks Felicity for sharing your photo and the way you made your coasters! You can also hang your coasters on the wall as wall art.
Here are some brilliant motivational wall coasters made by reader Joann. Thanks for sharing your photos Joann! Reader Staci made coasters as an anniversary gift for her boyfriend with photos of their favorite places in Kansas City. What a cool idea! Thanks for sharing your photo Staci! Reader Sarah made these gorgeous coasters with a fairytale castle design. Thanks for sharing your photo Sarah! This is a long page, but don't let that frighten you. Learning how to make tile coasters is actually really easy.
The only reason the page is long is because I've divided the tutorial up into small steps and included lots of photos. The first step in learning how to make coasters is to gather up your materials. Here's what you'll need Thanks to reader Lisa for the Home Depot link! For the glue, I recommend using Mod Podge or another reputable brand. I've tried using cheap white glues in the past, and some of them turn brown over time, which is heartbreaking after you put a lot of work into a project.
Tile coasters look awesome using photos instead of craft paper, but there are some special tips to make them turn out right. If you print your photos at home using an inkjet printer, then you need to use a different glue instead of Mod Podge. The Mod Podge is water based and makes inkjet-printed photos run.
So, instead of using Mod Podge, I'd recommend using a special glue designed specifically for inkjet prints. One glue that works well is "Annie Howes Glamour Seal", or else you can use a clear spray acrylic sealer that you can purchase from a craft store or hardware store. If you get your photos printed at a photo print shop e. Kinkos then the instructions on this page work just fine without any modifications. Some print shops will let you print 4x4" prints, which fit perfectly on a tile thank you Theresa for this tip!
Achieving a waterproof and non-tacky finish is the most critical part of how to make coasters in my opinion. Here's what you'll need:. It's a two-part epoxy that comes in two bottles which you mix together then pour on your coasters. People use it to coat bar-tops in bars and restaurants so it's designed to be durable. One coat of Envirotex is equivalent to 50 coats of regular varnish.
If you want to make a gift that will last for years, then it's worth using. The only thing that's not perfect about it is that it does stick a little bit to a hot coffee cup. Having said that, it's still much less tacky than any other finish I've tried in my experiments of how to make coasters. Before I discovered Envirotex I tried practically every other type of varnish including acrylic varnish, decoupage varnish, spray-on polyurethane varnish, araldite, egg whites, and mod-podge , and nothing gave as good a finish.
The other types of varnish looked OK, but they were tacky, or brittle, or got stained by coffee or tea. I haven't seen Envirotex in many craft stores, but you can get it at Amazon link above or on eBay. Some readers have said they've also spotted it in their local Michaels and Hobby Lobby craft stores. And obviously it's cheaper per tile if you buy it in bulk. I found this video not my own that does a great job of explaining how to make coasters and coat them with Envirotex.
Actually it describes how to make placemats, but the process for coasters is almost identical. If you have a slow internet connection you may prefer to follow my written instructions below instead.
Cut out squares of scrapbooking paper or photos to decorate your coasters. My tiles are 4" across, so I cut out pieces of scrapbooking paper 3. Make sure your tiles are clean and dry. If they're greasy, then give them a wipe with methylated spirits or rubbing alcohol to clean them. Completely paint the blank side of a decorative paper square with Mod Podge or white glue.
Make sure you go right up to the edges. It's best to work on a piece of scrap paper that you don't mind getting glue on. Place the glued piece of decorative paper onto a tile. Press on it firmly to remove any air bubbles. I recommend using a glass tumbler as a rolling pin and using a rolling motion from the center to the edge of the paper to work out any bubbles.
The first time I did this I just used my fingers and even though I thought I was thorough I still left some bubbles under the paper which I only noticed once the glue was dry. Repeat the process for the rest of the tiles. Have a cup of tea and a biscuit and wait 15 minutes for the glue to dry before going on to the next step.
Check for any bubbles under the paper. If you see any, pop them with a pin and flatten them out. Brush a layer of Mod Podge or white glue over the top of the decorative paper. I like to brush all in the same direction. Wait until the glue dries clear about 15 minutes , then paint on another layer, this time at right-angles to the first layer.
It's really important that you completely seal over the paper with glue, so that later the varnish doesn't soak into the paper and discolor it. Leave glue to dry overnight, so that it's completely dry before you apply the varnish in the next step.
Don't worry if the dried glue has a ridged surface texture from the brush strokes. When you varnish the coasters it will create a beautifully smooth surface and you won't see the ridges any more. I strongly recommend varnishing your tiles to make them waterproof. If you leave them unvarnished then they'll look OK, but they'll always have a slightly tacky sticky feel to them, and will stick to a hot cup placed on them. Also they'll stain if tea or coffee gets on them.
Varnishing your tiles with Envirotex will give them a glass-like waterproof finish which I think is really worth it. Mind you, the Envirotex epoxy varnish is going to drip everywhere when you pour it on your coasters, so before you start it's a good idea to:. The Envirotex smells a bit so you might want to work in a room with an open window. It not anywhere near as stinky as spray-on varnish though, which was something else I tried but wasn't happy with the results of along the way in my quest for how to make coasters waterproof.
Mark lines at 1oz and 2oz 30 mL and 60 mL on one of your disposable plastic cups. That's assuming you're making 4 coasters, each 4" square. If you're making more or less, you'll need to follow the instructions on the Envirotex package for how much you'll need. The way I marked the lines was to put exact amounts of water into the cup using digital scales and mark the level with a Sharpie marker.
You could also use measuring spoons to measure out the water. Make sure you completely dry the cup afterwards.